Owner Setup Guide
How to Program a Kwikset SmartCode Keypad
Call MD Locksmith for Kwikset SmartCode programming help; if you’re setting up your own lock, keep the door open and follow the model-appropriate steps below.
- Program your own code with the door open
- Steps for SmartCode models with Program and Lock buttons
- Know what a successful code entry looks and sounds like
- Get help from a locksmith open 24 hours a day
Get Your Kwikset SmartCode Keypad Ready to Program
These steps are for common SmartCode keypads that have an interior Program button and a Lock button on the keypad, including the SmartCode 909, 910, and 913. Button placement and programming details can differ by model, so check the model number on your lock before you begin.
- Keep the door open — Leave the door open throughout setup so the bolt cannot lock you out while you test the new code. Do not close the door until the code works as expected.
- Have your current access ready — Keep the working key with you and make sure you know the current programming code if your model requires one. These steps assume you already have authorized access to the lock.
- Choose a new user code — For the SmartCode 909, 910, and 913, choose a code that is 4 to 8 digits long. Pick one you can enter accurately, and keep it private.
- Check the batteries and buttons — Use the keypad and interior buttons only if they respond normally. If the lock has weak or inconsistent power, address that before trying to save a code.
- Identify your exact model — Use Kwikset’s official support and instructions to find details for your specific keypad. Models differ, especially in the way they manage programming codes and factory resets.
Kwikset SmartCode Programming: Enter and Test a User Code
On SmartCode 909, 910, and 913 keypads with the buttons described above, adding a user code follows this sequence. If your lock’s buttons or indicators do not match, pause and check the instructions for its model rather than trying another sequence.
- Leave the door open — Keep the door open while programming and testing. This lets you check the bolt without risking a lockout.
- Find the Program button — Open the door and locate the Program button on the interior side of the lock, near the battery area. Press it once.
- Enter your new code — Go to the exterior keypad and enter the new 4-to-8-digit user code you selected. Enter the digits in order without a long pause.
- Press the Lock button — Press the Lock button on the keypad once to submit the code. Do not press the interior Program button again during this sequence.
- Check the response — On these models, a green flash and one beep indicate successful programming. A red flash with three beeps signals that the entry was not accepted; check the code length and repeat the sequence once.
- Test the code with the door still open — Enter the new code and press the Lock button. Confirm that the lock responds as expected, then use the key to check the lock’s operation before closing the door.
- Add other codes only if needed — If you want another user code, repeat the programming sequence for that lock. The number of codes a keypad can store varies by model, so check its instructions before adding more.
Need help now? (240) 366-2739
Why a Kwikset SmartCode May Reject a New Code
If the keypad does not save your entry, stop and check these common setup issues before trying again.
The code does not meet the model’s requirements
A code that is too short or too long may be rejected. The 909, 910, and 913 use 4-to-8-digit user codes; confirm the required length for any other model.
The buttons were pressed in the wrong order
For the models covered here, press Program once, enter the new code, then press Lock once. Starting over with that sequence can correct a missed or repeated button press.
The keypad or lock has a power problem
A keypad that fails to respond consistently may not complete programming. Check the battery condition and the model’s battery instructions before attempting setup again.
Your model uses different programming steps
SmartCode models do not all use the same controls or reset process. Check the instructions for the exact model instead of applying a reset sequence meant for another lock.
When to Call a Locksmith About Your SmartCode Keypad
Call a locksmith if the keypad will not accept a code after you have checked the model and followed its programming sequence, or if the lock behaves unpredictably during setup. A factory reset can erase stored codes and may require additional setup, so use the exact model’s published instructions rather than guessing. If you cannot enter the property or do not have the key or current code, do not try to defeat the lock; call MD Locksmith at (240) 366-2739. We can also help with Kwikset SmartCode keypad lock help or you can contact us.
Need help now? (240) 366-2739
Frequently asked questions
Can I program a Kwikset SmartCode keypad while the door is closed?
Keep the door open while you program and test a code. That way, you can confirm the lock responds before you secure the door.
How do I change the code on a Kwikset keypad?
For SmartCode 909, 910, and 913 models with a Program button, press Program once, enter the new 4-to-8-digit code, then press Lock once. Test it with the door open; other models may use different steps.
How do I reset a Kwikset SmartCode lock?
A factory reset can erase stored user codes, and the reset sequence varies by model. Identify the exact model and use its published instructions before resetting; contact a locksmith if you are unsure or the lock is not responding.
What should I do if my SmartCode keypad flashes red and beeps?
On the SmartCode 909, 910, and 913, a red flash with three beeps means the code entry was not accepted. Check the code length and button sequence, then use the model-specific instructions if the keypad still rejects it.
Need Help With Your Kwikset SmartCode?
Call MD Locksmith at (240) 366-2739. We’re open 24 hours a day, 7 days a week.